|
|
Lights
Our high tech LED light design can be used to place as incandescent lighting in street rods, custom cars or any vehicle.
Why use Hylites?
- Standard super bright white LED's
- Even pattern for reading or accenting
- Adjustable to highlights specific areas or use as indirect lighting
- Built in power savers Smart Switch for automatic off (in most models)
- CNC machined billet aluminum housing
- Made in the USA
- Quality LED's 100,000 hours average life (11+ yrs. constant on)
- Draws 10% the power of the average 800ma. dome light. (1amp-1000ma.
- Two wire (+12vdc ground) connections.
- Clean invisible mount.
HLM lites
Tylites
TyLites are a unique way to add lighting to your custom motorcycle or engine compartment. Use to wrap around frames, wire clusters, looms, lines, under dash, under seats or any unusual shape. TyLites mount without any drilling, glueing or taping. The combination of a special black tyrap and machined billet aluminum will give you flexibility to hide or expose these stylish lights.
All models include the best and brightest high output LED's with 100,000 hours average life or 11+ years of constant on. Each light comes complete with 4 feet of black twin lead wire and internal current limiting, connect directly to any 12vdc source. All TyLites are weatherproof and can be mounted anywhere. US made not cheap imports.
All TyLites come standard with super bright White LED's or order any TyLite with your choice of LED Colors: RED, BLUE, GREEN, YELLOW, ORANGE, at No Additional Charge. PURPLE cost more and must be phone ordered.
|
Controllers and indicators
Micro Tech Series
Window switches
HyLites MicroTech series controllers and indicators finally simplify complicated relay and control problems. Our instructions will make it easy for even a novice to wire our controls. We use the latest in microelectronics and billet aluminum to provide an attractive look to your rod or custom.
Why use a 40 amp. switch to control a 1/10 amp. relay coil? The
HMT-2M
is only 1/2"H x 1 1/2"L sleek machined billet aluminum bezel with two billet momentary pushbutton switches. The
HMT-4M
is 1/2"H x 2 1/2" L, bezel is 1/8" D. When used in conjunction with our
HMT-2R
relay module you can control Power windows, Trunk, hood, etc. Another benefit of only controlling a 1/10 amp. relay coil is the small cable required to be run to the relay module. This gives you great flexability in mounting and placement of the switches. Window switches don't need to be mounted close to the window motor. Mount them in an over head console, dash or anywhere you choose.
Antennas
Tune Trapper
Am-Fm Tuned Hidden Antenna By ECS
Street rods, Customs, Motorcycles, Boats, RV's. . .
Our universal hidden antenna's have a Money Back Guarantee!!!
If you have had a bad experience in the past with hidden antenna's, so have we, and that's why we designed a universal hidden FM antenna that works! For a clean look on your Rod, Custom or Cruiser . Mount in any vehicle, Boat, RV or Motorcycle. The Tune Trapper antenna was designed to be hidden. Mount anywhere, in any position, in steel or fiberglass. Most vertical whip antennas are a 1/4 wave ground plane. The TT is a full 1/2 wave helical dipole, wound with several feet of wire and requires no ground. Each TT is hand tuned to resonance with special instruments. We use 95% braided sheild cable for virtual elimination of EMI electrical noise caused by engines, fans, wipers, etc. Beware of mini amplified antennas that make big claims. The TT antenna will not cause radio overload problems associated with amplified antenna's. These hand tuned USA made antenna's require no power. Your radio has all the preamp it needs built in, it's just looking for a properly tuned antenna to make it rock. Every TT is tested before being packaged. We guarantee it will perform. The TT no ground plane design works well on all vehicles. . for Anything that Rocks, Rolls, Floats or Flies.
Lite Accessories
Other stuff
|
|
